DEER PARK, TX 77536 - US
ZACHRY is currently seeking an experienced Industrial Instrument Fitter.
Instrument Fitters will work with both electrical and piping systems to install the required tubing and instruments for the system to be measured and/or controlled.
Must have 4+ years’ experience in instrumentation
Must be able to read blue prints.
Must be able to work on low and high pressure tubing/piping systems.
Must have tools (see tool list below).
Must be able to work with precision instruments and tools.
Must be willing to follow all company and project work policies and procedures.
Will read prints and P&IDs to interpret the work to be completed, the required equipment, and required tools to perform assigned work.
Will work with piping systems to install instrumentation in order for the system to work properly, be controlled, and/or monitored.
Will work with precision tools to calibrate instrumentation and to adjust installed electrical and piping components.
Will work with the installation, manipulation, and fabrication of piping and tubing according to specifications.
May need to assist in other duties including but not limited to installing pipe, tubing, and piping/tubing components.
Must have 4+ years’ experience in instrumentation or illustrate comparable level of knowledge.
Required to have all journeymen tools and have experience with associated power tools.
Must be able to measure, cut, bend, thread, assemble and install primary piping and tubing.
Must be able to read and interpret drawings, blueprints and P & IDs.
Must be able to check performance using testing and measuring. Instruments and make necessary adjustments.
Must be able to work with low and high pressure tubing/piping systems.
Must have reliable transportation to and from work.
Must be willing to follow all company and project policies, rules, and guidelines.
Must be willing to assist in any additional qualified duties assigned.
Current, ROF’ed, or Former Employee.
Have formal education or vocational training.
Experience in instrumentation on a combined-cycle power plant.
Employee will be required to adhere to large amounts of standing, walking, bending, squatting and lifting.
Will use arms and hands to signal, grab, hold, turn, push, and pull: objects, materials, controls and tools.
May be required to lift, carry and move up to 50lbs.
Must be able to work at heights and be able to climb ladders and stairways as well as work on elevated platforms
Will as needed work at heights, climb ladders and stairways and work off of platforms. Will work at heights up to 300’ utilizing proper fall protection.
Must be capable of working outside in the elements including heat, cold, rain, snow and wind
Will be required to wear personal protective equipment (PPE) including but not limiting to hard hat, safety glasses, gloves, fall arrest harness, face shield, ear plugs, and goggles.
Required tool list:
1 - Metal Tool Box with Lock
1 - Tubing Benders (1/4", 3/8", 1/2")
1 - Pair of Leather Gloves
1 - Tool Pouch with Belt
1 - 50' or 100' Tape Measure
1 - Hacksaw
1 - 9" Klein Side Cutters
1 - 8" Diagonal Pliers
1 - 8" Needle Nose Pliers
1 - Cold Chisel
1 - Pocket Knife
2 - Crescent Wrenches (8" & 12")
1 - Channel Locks
1 - Torpedo Level
1 - Wire Strippers
1 - Tape Measure 12' to 25'
1 - Combination Square
1 - Allen Wrench Set
1 - Protractor Level
1 - Flashlight
1 - Plumb Bob
1 - Kevlar Gloves
1 - Combination Wrenches 3/8",7/8"
1 - Ratchet Crimper
1 - Tubing Cutter Set
1 - Center Punch
1 - Hammer (Ball Peen or Claw)
1 - Screwdrivers 6" to 10" (Slotted & Phillips)
1 - Nut Driver Set 3/8", 7/16", 1/2", 9/16"
1 – Rain Coat / Rubber boot
ZACHRY is dedicated in providing a Safe and Drug Free work environment; and is an Equal Opportunity Employer.